氣動量?jì)x作為高精密測控工具,在工件長度測量方面有著重要應用,可以測量?jì)葟?、外徑、槽寬、兩孔距、深度、厚度、圓度、錐度、同軸度等數據,適用于在大批量生產中測量?jì)?、外尺寸,也可用于測量孔距和軸孔配合間隙。氣動量?jì)x的精度要求很高,穩定性也必須達標,否則測量數據就會(huì )出現不準確等情況,影響工件生產標準。
氣動量?jì)x穩定性差主要原因在于兩大類:
一是制作原因自身質量不達標,即制作有問題;
二是人為操作不當,即使用有問題。
一、制造原因
1、結構設計不合理
氣動量?jì)x的機械結構設計不合理易引起量?jì)x不穩定。其定型設計很重要,首先要考慮量?jì)x的剛性,如果機械結構剛性差,一旦收到外界微量影響,如地基微量振動等都會(huì )引起高精度氣動量?jì)x不穩定。
2、部件材料不匹配
主要部件是傳感器和控制電箱的不匹配。因為不同傳感器材料阻抗和靈敏度都不同,它對應的電路也不同。同理與傳感器兩線圈組成橋路的激勵電源變壓器兩個副邊繞組也不可能wan全對稱。所以若傳感器和輸入電路不進行阻抗匹配,它的殘余電壓就很大,則非線性誤差增大,在零位附近測到的信號很不穩定。有些制造商因沒有條件做傳感器,就借用別人的傳感器,在電路上只做簡單的放大倍數調整,而不做阻抗匹配調整。這樣,看上去整機是可以測量的,但它的穩定性卻不好。
3、控制線路不穩定
電氣控制線路本身的穩定性將直接影響整臺氣動量?jì)x的穩定性。一般高精度氣動量?jì)x的線路由輸入電橋;振蕩線路;相敏檢波或脈沖箝位檢波;濾波放大和顯示、記錄四部分組成。其中振蕩線路的電壓作為激勵電源供量?jì)x輸入橋路用,振蕩電壓的不穩定就會(huì )引起輸入信號的不穩定
二、使用原因
1、環境不符合要求
氣動量?jì)x對于使用環境要求很高,所以使用時一定要符合環境要求,如果不符合要求,就會(huì )出現氣動量?jì)x不穩定的現象。使用環境一般要求溫度為10~40℃,環境濕度在40%以下,周?chē)h(huán)境要求必須保持清潔,不能有腐蝕性灰塵等。
2、地基穩定性不好
地基對穩定性有直接影響,因為如果地基有振動將引起整臺儀器的振動,在高倍率下就會(huì )使測量穩定性下降,所以應遠離振源。有些精度特別高的儀器還應在地下室的避振房里使用。
3、人員操作不恰當
氣動量?jì)x的正確使用是保證每次測量成功的關鍵。測量要求精度較高的零件的測力要放得很小,否則會(huì )因測力過大,而在事實上造成有一個力加在被測零件上,使得被測零件在旋轉時有微量的移動,從而造成每次測得的數據不一樣,表面看上去是儀器的穩定性差,實際上是用戶使用不當造成。
氣動量?jì)x穩定性差原因有哪些大致如上所述,要想保證氣動量?jì)x穩定性好,就要從制作與使用兩方面著手解決,生產廠家要確保制造的氣動量?jì)x質量過關,同時操作人員要采用正確使用方式使用氣動量?jì)x。
上一篇 : 印刷機怎樣對基準點?
下一篇 : 氣動量?jì)x在壓縮機中的具體應用