氣動量?jì)x目前基本上都實際浮標氣動量?jì)x升級為數顯氣動量?jì)x,價格相不多。數顯的顯示分辨率0.0001mm 當產品不合格時,紅色光標顯示,并顯示實際測量尺寸,是否合格。測量速度快,精度高。
不管哪種儀器,用的時間長了都會(huì )出現些問題,像氣動量?jì)x這種精密量具經長時間使用后,量?jì)x會(huì )出現多種故障,更應實行定期檢定和保養,才能避免使用時發生不必要的故障。小編就給大家詳細的介紹下氣動量?jì)x維護中常見故障的排除,希望對大家有所幫助。
1.氣動量?jì)x測量產品時,數據在變小是什么原因?
可能是氣壓不穩定會(huì )造成這樣的現象;
2.氣動量?jì)x測量時,校正沒有多長時間測量又不準了?
有可能是測量頭磨損了,試著調整一下倍率旋鈕??纯词欠衲苷{整過來,如果不可以,可以聯系寧波森泉科技有限公司定制各種內徑 外徑 錐度 同心度 平行度測量座;
3.氣體流量不足:測量時,浮標會(huì )從正常示值位置下降,出現示值波動不穩,這是種不正常的現象,主要原因是由于穩壓器性能不好或各氣路有堵塞現象而造成氣體流量不足。這種情況需要檢查供氣壓力是否在0.4~ 0. 7 MPa范圍內??捎?/span>1.6MPa以下的壓力表校準穩壓器并調整到規定的壓力范圍。測量時應經常用標準環規校對零位;
4.電子故障:如電箱按鍵失靈,可系統總清、換新面膜;如軸不計數,可換滑座或整個尺、重新接下信號線、換主機板等。如數碼管缺筆劃,則需更換或維修;
5.精度故障:包括氣動量?jì)x軸精度不準、兩坐標測量精度差、角度示值誤差大、不同平面測量誤差大等。應對此類故障,要注意校正和調整;
6.氣源壓力不穩定:氣源壓力的較大變化對量?jì)x指示值有影響。氣源壓力是否在0.4~ 0.7 MPa區域,可用壓力表檢查,超出范圍時,應檢修量?jì)x穩壓器;
7.浮標量?jì)x與數顯量?jì)x哪個好?
一般推薦數顯的氣動量?jì)x。a.數字顯示 可以顯示到0.0001MM b.數據可以保存 c.可以存儲10組測量數據 ;
8.不合格直接紅標顯示 ;
9.價格也美麗;
上一篇 : 機加工表面粗糙度檢測